What this industry manufactures
Furniture makers, interior fabricators, signage and decor workshops and artists apply a clear epoxy coat as the last step on a finished piece. The substrate is already built — timber, ply, MDF, stone, a printed or painted surface, a canvas — and the epoxy is there to seal it, lift the colour underneath and leave a hard gloss the surface could not achieve on its own.
Why Epoxy Art Resin is suitable
Epoxy Art Resin is published as a two-component, water-clear system that mixes at 2:1 to a viscosity of 900-1200 cPs at 25 °C and cures over 24 hours to a high-gloss finish. The TDS describes it as self-levelling with bubble release and UV stabilised, stating that it resists yellowing. Those four properties are precisely what a coating pour needs: thin enough to flow out flat rather than sit where it lands, slow enough to let trapped air rise before it gels, and stabilised so a clear film over a visible surface does not go amber. Read the published data on the Epoxy Art Resin product page before selecting.
Required resin characteristics
- 01The substrate and its condition — bare timber, sealed board, stone, a print or a painted surface each behave differently under a flood coat
- 02The surface area to be coated, so the quantity can be worked out against 15 kg packs and the 100 kg minimum order
- 03Whether the piece is indoors or will see direct sun, and for how long
- 04Working temperature in the workshop, since both viscosity and cure time are quoted at 25 °C
- 05Whether a pigment, dye or metallic effect is going into the coat
Manufacturing process
This is a product-selection page, not an application manual. What the published data does establish is the mix ratio and the cure window; what it does not establish is a pour thickness per coat, a recoat interval, a surface-preparation specification, a sanding or polishing schedule, or an adhesion result on any particular substrate. Those depend on the piece, the workshop and the surface being coated, and should be confirmed against the current TDS and a trial on your own substrate rather than assumed. Epoxy Hardener is a separate product with its own published role — see how the two components differ.
Advantages
- Uses Epoxy Art Resin's own published mix ratio, viscosity, cure time and UV positioning
- Separates the coating role from the casting role rather than treating clear epoxy as one product
- Keeps liquid-resin data distinct from the finished surface's durability
- Names what a buyer should confirm on their own substrate before committing to a quantity
Common products produced
- Epoxy-coated wooden and live-edge table tops
- Bar, counter and reception-desk surfaces
- Decorative wall and interior panels
- Artwork, photo and print surface coats
- Signage and display faces
Frequently asked questions
They are published for different roles. Art Resin is the self-levelling coating product, mixed 2:1 and poured as a film over a finished surface. Epoxy Clear Casting Resin is published for filling depth, such as a river-table channel or a mould. Casting resin vs coating resin sets out the choice in full.
No pour thickness is published for this grade, so no figure should be assumed from a general epoxy description. Thickness, recoat interval and any depth limit belong to the current TDS and to a trial on your own piece. Deep pours are a casting question rather than a coating one.
The TDS states that the grade is UV stabilised and resists yellowing. That is a formulation statement about the supplied resin, not a warranty on a finished piece over a given number of years in a given location. Outdoor and direct-sun exposure should be raised in the enquiry rather than inferred.
Coverage depends on the area and the film thickness you are pouring, neither of which is fixed by the product data. Share the surface dimensions and the number of coats intended along with your enquiry. Epoxy Art Resin is supplied in 15 kg packs with a 100 kg minimum order quantity.
The published data gives a 24-hour cure and a high-gloss finish; it does not publish hardness, scratch resistance, heat resistance or food-contact status. Where the finished surface has a service requirement of that kind, state it in the enquiry so the requirement can be reviewed against the available documentation.
Coating a surface in clear epoxy?
Send the substrate, the surface area, whether the piece will see direct sun, and the quantity and delivery location, so the right published grade can be confirmed before you order.